Untitled Document

Welcome to ILiftIt.com! Selling the best home hobby car lifts on the market.

follow us on twitter

Quality Lifts 2-Post Floor Plate Car Lift

Quick Overview

9,000 lb. Lifting Capacity Car Lift / Symmetric / Asymmetric Lifting Capabilities
Model: QFP09

Availability: In stock

$3,295.00
OR

More Views

Details

This 2-post car lift model QFP09 by Quality Lifts is ideal for low ceiling applications. This lift is designed with 3-stage front arms and double telescoping arm pads for maximum vehicle lifting flexibility. Whether using this two post lift for commercial use or for home storage, you cannot go wrong. Quality Lifts offers power units in 110v or 220v configurations for more power flexibility. Designed for longevity, the QFP09 features a heavy-duty chain lifting system with cable equalization.

With a 9.000 lb. the lifting capacity the QFP09 2-post lift can lift trucks or other frame vehicles utilizing its optional accessories of frame engaging adapters. The frame engaging adapters is a REQUIREMENT when working with trucks and other frame vehicles.

Other people marked this product with these tags:

Use spaces to separate tags. Use single quotes (') for phrases.

  • 9,000-pounds lifting capacity
  • 10’ 7/8" overall column height is ideal for low ceiling
  • 3-Stage Front and Rear Arms
  • Heavy duty chain over electric hydraulic in operation with cable equalization
  • Heavy duty column construction
  • Dual point mechanical pull-lock cable release
  • NEW! Optional 115v Power Unit for Home Use
  • Availble in 110v or 220v power unit
  • Colors: BLUE ONLY



Specifications

 

Lifting Capacity: 9,000 lbs.
Rise Height (screw pads highest position) *1: 78-1/8"
Column Height: 10'-7/8"
Drive-Thru Clearance: 98-3/16"
Front Arm Reach (Min/Max): Min: 24-1/2" / Max: 44-1/2"
Rear Arm Reach: Min: 24-1/2" / Max: 44-1/2"
Screw Pad Height *2: Min: 4" or  Max: 5-7/8"
Inside of Columns: 109"
Ceiling Height Required: 10' 1-7/8"
Motor: 1HP or 2HP Single Phase, 60Hz
Voltage: 1HP/115v or 2HP/208-230v Single Phase, 60Hz (Optional – 2HP, Three Phase, 50/60Hz,for 208 or 230 or 460)
Max. Load Per Arm: 2,250 lb.
Lifting Time: 60 seconds (approximate)
Shipping Weight:  1700 lbs.

 

*Lift capacity ratings are based on loads equally distributed on all four arms
*1 Rise height measure with telescoping screw pad in highest position
*2 Specifications are listed without rubber pad for measurements with rubber pad add 1/4” (6mm)

Installation, Operation & Maintenance Manual Four Post Surface Mounted Lift

 

2-post lift installation 2-post lift installation
Fig 1a - General Specifications
(click image to enlarge) 
Fig 1b - Service Bay Layout
(click image to enlarge) 

 

Model: QFP09

 

Vertical Clearance

Check the height of the area where the lift is to be installed. Clearance should be calcualted based on the full raised height of the lift. WARNING: Failure by purchaser to provide adequate clearance could result in unsatisfactory ift performance, property damage, or persoanl injury.

 

Flooring

Be certain you have the proper concrete floor to properly handle the loaded lift. Floor should be in generally good condition with no large cracks,spalling or deterioration.

 

Minimum requirements for concrete are 4 inches minimum depth, with steel reinforcement, 3500 psi, cured for 28 days perlocal commercial practice. This lift is designed to accommodate a 3 inch total variation in elevation at the base of the four posts. Floor should be levelwithin 1/2 inch from side-to-side and 2 1/2 front-to-rear to avoid special shimming. No anchors should be installed within 8 inches of any crack, edge, or expansion joint. If these conditions cannot be met, a pad may be poured to accommodate the lift.

 

Check with local building inspectors and/or permits office for any special instructions or approvals required for your installation. WARNING: Failure by purchaser to provide the recommended mounting surface could result in unsatisfactory lift performance,property damage, or personal injury. 


Location

This lift has been evaluated for indoor use only with an operating ambient temp. range of 5 – 40°C (41-104°F)

 

Electrical Requirements

For lift installation and operation for single phase units, it is necessary to have a dedicated circuit with a double pole 25 amp circuit breaker or time delay fuse.

 

Safety Notices and Decals

For your safety, and the safety of others, read and understand all of the safety notices and decals included here.


READ ENTIRE MANUAL BEFORE ASSEMBLING, INSTALLING, OPERATING, OR SERVICING THIS EQUIPMENT. PROPER MAINTENANCE AND INSPECTION IS NECESSARY FOR SAFE OPERATION. DO NOT OPERATE A DAMAGED LIFT.


Safety decals similar to those shown here are found on a properly installed lift. Be sure that all safety decals have been correctly installed on the Power Unit reservoir. Verify that all authorized operators know the location of these decals and fully understand their meaning. Replace worn, faded, or damaged decals promptly. 

 

WARNING: Do not attempt to raise a vehicle on the lift until the lift has been correctly installed and adjusted as described in this manual.


Receiving

The shipment should be thoroughly inspected as soon as it is received. The signed bill of lading is acknowledgement by the carrier of receipt in good condition of shipment covered by our invoice.


If any of the goods called for on this bill of lading are shorted or damaged, do not accept them until the carrier makes a notation on the freight bill of the shorted or damaged goods. Do this for your own protection.


NOTIFY Quality Lifts AT ONCE if any hidden loss or damage is discovered after receipt. IT IS DIFFICULT TO COLLECT FOR LOSS OR DAMAGE AFTER YOU HAVE GIVEN THE CARRIER A CLEAR RECEIPT.


File your claim with Quality Lifts promptly. Support your claim with copies of the bill of lading, freight bill, and photographs, if available.

 

CLICK HERE TO DOWNLOAD FULL INSTALLATION MANUAL