Untitled Document

Welcome to ILiftIt.com! Selling the best home hobby car lifts on the market.

follow us on twitter

Quality Lifts 2-Post Car Lift | Truck Lift

Quick Overview

10,000 lb. Lifting Capacity Car Lift | Truck Vehicle Lift | Symmetric or Asymmetric Lifting
Model: Q10

Availability: In stock

$2,995.00
OR

More Views

Details

This ETL Certified two-post car lift / truck lift model Q10 by Quality Lifts is ideal for light duty trucks. This lift is designed with 3-stage front arms and 2-stage rear arms for maximum vehicle lifting flexibility. Whether using this 2 post vehicle lift for commercial use or for home storage, you cannot go wrong. Quality Lifts offers standard power units in single phase support voltages of 208-230v. Designed for longevity, the Q10 features full size cables made of steel for longer life and use.

The Q10 2-post lift has a 10.000 lb. the lifting capacity suitable for lifting trucks or other frame vehicles utilizing its optional accessories of frame engaging adapters. The frame engaging adapters is a REQUIREMENT when working with trucks and other frame vehicles.

Other people marked this product with these tags:

Use spaces to separate tags. Use single quotes (') for phrases.

ETL ALI Certified Lifts

  • 10,000-pounds lifting capacity
  • Max Load per Arm: 2,500 lb.
  • Higher Rise with 71" Stroke Cylinder
  • Rise Height of 78.75" Provides Excellent Underneath Clearance
  • Adjustible Overhead For Max Clearance or Protection Against Lower Obstructions
  • Symmetric or Asymmetric Lifting
  • Optional Drop In Truck Adapters
  • Full Size Cables and Steel Cables for Longer Life
  • Single Point Lock Release
  • Rubber Door Protector
  • Powder Coat Paint Blue
  • Space and Concrete Must Meet Minimum Requirements (see Q10 Install Option)
  • Colors: BLUE ONLY
  • ETL Certified



Specifications 

Lifting Capacity*: 10,000 lbs.
Rise Height (screw pads highest position): 77-3/4"
Overall Height (Adjustable): 147-1/2" / 137-1/2"
Overall Width
: 131 3/4"
Drive-Thru Clearance: 98-3/8"
Floor to Overhead Switch: 140 1/2" / 130 1/2"
Short Arm Reach: Min: 21-3/4" - 39-1/4"
Long Arm Reach: 38-1/4" - 55-3/8"
Screw Pad Height: 4-1/4" - 6-3/4"
Inside of Columns: 110 1/4"
Cylinder Height: 148-3/4"
Ceiling Height Required: 149"
Motor: 2HP,Single Phase, 60Hz
Voltage: 208-230
Max. Load Per Arm: 2,550 lb.
Speed of Rise**: 52 seconds
Shipping Weight:  1700 lbs. 

*Lift capacity ratings are based on loads equally distributed on all four arms.
**Lifting and lowering speeds may vary depending on the weight of the vehicle.

Installation, Operation & Maintenance Manual Four Post Surface Mounted Lift

 

2-post lift installation 2-post lift installation
Fig 1a - General Specifications
(click image to enlarge) 
Fig 1b - Service Bay Layout
(click image to enlarge) 

 

Model: Q10

 

Vertical Clearance

Check the height of the area where the lift is to be installed. Clearance should be calcualted based on the full raised height of the lift. WARNING: Failure by purchaser to provide adequate clearance could result in unsatisfactory ift performance, property damage, or persoanl injury.

 

Flooring

Be certain you have the proper concrete floor to properly handle the loaded lift. Floor should be in generally good condition with no large cracks,spalling or deterioration.

 

Minimum requirements for concrete are 4 inches minimum depth, with steel reinforcement, 3500 psi, cured for 28 days perlocal commercial practice. This lift is designed to accommodate a 3 inch total variation in elevation at the base of the four posts. Floor should be levelwithin 1/2 inch from side-to-side and 2 1/2 front-to-rear to avoid special shimming. No anchors should be installed within 8 inches of any crack, edge, or expansion joint. If these conditions cannot be met, a pad may be poured to accommodate the lift.

 

Check with local building inspectors and/or permits office for any special instructions or approvals required for your installation. WARNING: Failure by purchaser to provide the recommended mounting surface could result in unsatisfactory lift performance,property damage, or personal injury. 


Location

This lift has been evaluated for indoor use only with an operating ambient temp. range of 5 – 40°C (41-104°F)

 

Electrical Requirements

For lift installation and operation for single phase units, it is necessary to have a dedicated circuit with a double pole 25 amp circuit breaker or time delay fuse.

 

Safety Notices and Decals

For your safety, and the safety of others, read and understand all of the safety notices and decals included here.


READ ENTIRE MANUAL BEFORE ASSEMBLING, INSTALLING, OPERATING, OR SERVICING THIS EQUIPMENT. PROPER MAINTENANCE AND INSPECTION IS NECESSARY FOR SAFE OPERATION. DO NOT OPERATE A DAMAGED LIFT.


Safety decals similar to those shown here are found on a properly installed lift. Be sure that all safety decals have been correctly installed on the Power Unit reservoir. Verify that all authorized operators know the location of these decals and fully understand their meaning. Replace worn, faded, or damaged decals promptly. 

 

WARNING: Do not attempt to raise a vehicle on the lift until the lift has been correctly installed and adjusted as described in this manual.


Receiving

The shipment should be thoroughly inspected as soon as it is received. The signed bill of lading is acknowledgement by the carrier of receipt in good condition of shipment covered by our invoice.


If any of the goods called for on this bill of lading are shorted or damaged, do not accept them until the carrier makes a notation on the freight bill of the shorted or damaged goods. Do this for your own protection.


NOTIFY Quality Lifts | ILiftIt.com AT ONCE if any hidden loss or damage is discovered after receipt. IT IS DIFFICULT TO COLLECT FOR LOSS OR DAMAGE AFTER YOU HAVE GIVEN THE CARRIER A CLEAR RECEIPT.


File your claim with ILiftIt.com | Quality Lifts promptly. Support your claim with copies of the bill of lading, freight bill, and photographs, if available.

 

CLICK HERE TO DOWNLOAD FULL INSTALLATION MANUAL